I14-Hard X-ray Nanoprobe
|
Diamond Proposal Number(s):
[20420, 28521]
Open Access
Abstract: All-perovskite tandem solar cells beckon as lower cost alternatives to conventional single-junction cells. Solution processing has enabled rapid optimization of perovskite solar technologies, but new deposition routes will enable modularity and scalability, facilitating technology adoption. Here, we utilize 4-source vacuum deposition to deposit FA0.7Cs0.3Pb(IxBr1–x)3 perovskite, where the bandgap is changed through fine control over the halide content. We show how using MeO-2PACz as a hole-transporting material and passivating the perovskite with ethylenediammonium diiodide reduces nonradiative losses, resulting in efficiencies of 17.8% in solar cells based on vacuum-deposited perovskites with a bandgap of 1.76 eV. By similarly passivating a narrow-bandgap FA0.75Cs0.25Pb0.5Sn0.5I3 perovskite and combining it with a subcell of evaporated FA0.7Cs0.3Pb(I0.64Br0.36)3, we report a 2-terminal all-perovskite tandem solar cell with champion open circuit voltage and efficiency of 2.06 V and 24.1%, respectively. This dry deposition method enables high reproducibility, opening avenues for modular, scalable multijunction devices even in complex architectures.
|
May 2023
|
|
E02-JEM ARM 300CF
I14-Hard X-ray Nanoprobe
|
Stuart
Macpherson
,
Tiarnan A. S.
Doherty
,
Andrew J.
Winchester
,
Sofiia
Kosar
,
Duncan N.
Johnstone
,
Yu-Hsien
Chiang
,
Krzysztof
Galkowski
,
Miguel
Anaya
,
Kyle
Frohna
,
Affan N.
Iqbal
,
Satyawan
Nagane
,
Bart
Roose
,
Zahra
Andaji-Garmaroudi
,
Kieran W. P.
Orr
,
Julia E.
Parker
,
Paul A.
Midgley
,
Keshav M.
Dani
,
Samuel D.
Stranks
Diamond Proposal Number(s):
[24111, 20420]
Abstract: Understanding the nanoscopic chemical and structural changes that drive instabilities in emerging energy materials is essential for mitigating device degradation. The power conversion efficiency of halide perovskite photovoltaic devices has reached 25.7% in single junction and 29.8% in tandem perovskite/silicon cells1,2, yet retaining such performance under continuous operation has remained elusive3. Here, we develop a multimodal microscopy toolkit to reveal that in leading formamidinium-rich perovskite absorbers, nanoscale phase impurities including hexagonal polytype and lead iodide inclusions are not only traps for photo-excited carriers which themselves reduce performance4,5, but via the same trapping process are sites at which photochemical degradation of the absorber layer is seeded. We visualise illumination-induced structural changes at phase impurities associated with trap clusters, revealing that even trace amounts of these phases, otherwise undetected with bulk measurements, compromise device longevity. The type and distribution of these unwanted phase inclusions depends on film composition and processing, with the presence of polytypes being most detrimental for film photo-stability. Importantly, we reveal that performance losses and intrinsic degradation processes can both be mitigated by modulating these defective phase impurities, and demonstrate that this requires careful tuning of local structural and chemical properties. This multimodal workflow to correlate the nanoscopic landscape of beam sensitive energy materials will be applicable to a wide range of semiconductors for which a local picture of performance and operational stability has yet to be established.
|
May 2022
|
|
E02-JEM ARM 300CF
I14-Hard X-ray Nanoprobe
|
Tiarnan A. S.
Doherty
,
Dominik
Kubicki
,
Stuart
Macpherson
,
Young-Kwang
Jung
,
Duncan
Johnstone
,
Affan
Iqbal
,
Dengyang
Guo
,
Kyle
Frohna
,
Mohsen
Danaie
,
Elizabeth
Tennyson
,
Satyawan
Nagane
,
Anna
Abfalterer
,
Miguel
Anaya
,
Yu-Hsien
Chiang
,
Phillip
Crout
,
Francesco Simone
Ruggeri
,
Sean
Collins
,
Clare
Grey
,
Aron
Walsh
,
Paul
Midgley
,
Samuel
Stranks
Diamond Proposal Number(s):
[20420, 24111]
Abstract: There is currently substantial interest in stabilizing the simple ternary FAPbI3 perovskite because of its near-optimal band gap and superior thermal stability compared to methylammonium-based materials.1 The key challenge of FAPbI3 is the thermodynamic instability of the polymorph required for efficient light harvesting. Without additives, the black photoactive α-polymorph is only stable above ca. 160°C. At room temperature, it is metastable and rapidly transitions to the non-perovskite yellow polymorph. The stabilization of the black polymorph at room temperature can be achieved, for example, by adding a small amount of the pernicious MA through use of methylammonium chloride (in conjunction with formamidinium formate),2 methylammonium thiocyanate,3 or methylammonium formate.4 We have developed a new stabilization strategy which does not involve the addition of MA.5 Instead, it uses a surface-templating agent (EDTA) which modifies the material without incorporating into the structure. We use a combination of scanning electron diffraction (SED) and nuclear magnetic resonance spectroscopies (NMR, NQR) to identify the atomic-level mechanism of action of EDTA in this role. We find that it templates the structure by inducing a small octahedral tilt, only resolvable with local characterization techniques, and imparts remarkable phase stability by arresting transitions to low-dimensional polymorphs. This octahedral tilt engineering strategy is remarkably universal, and we show that it is the intrinsic stabilization mechanism in the state-of-the-art FA-rich mixed-cation materials.
|
Feb 2022
|
|
E02-JEM ARM 300CF
I14-Hard X-ray Nanoprobe
|
Tiarnan A. S.
Doherty
,
Satyawan
Nagane
,
Dominik J.
Kubicki
,
Young-Kwang
Jung
,
Duncan N.
Johnstone
,
Affan N.
Iqbal
,
Dengyang
Guo
,
Kyle
Frohna
,
Mohsen
Danaie
,
Elizabeth M.
Tennyson
,
Stuart
Macpherson
,
Anna
Abfalterer
,
Miguel
Anaya
,
Yu-Hsien
Chiang
,
Phillip
Crout
,
Francesco Simone
Ruggeri
,
Sean M.
Collins
,
Clare P.
Grey
,
Aron
Walsh
,
Paul A.
Midgley
,
Samuel D.
Stranks
Diamond Proposal Number(s):
[20420, 24111]
Abstract: Efforts to stabilize photoactive formamidinium (FA)–based halide perovskites for perovskite photovoltaics have focused on the growth of cubic formamidinium lead iodide (α-FAPbI3) phases by empirically alloying with cesium, methylammonium (MA) cations, or both. We show that such stabilized FA-rich perovskites are noncubic and exhibit ~2° octahedral tilting at room temperature. This tilting, resolvable only with the use of local nanostructure characterization techniques, imparts phase stability by frustrating transitions from photoactive to hexagonal phases. Although the bulk phase appears stable when examined macroscopically, heterogeneous cation distributions allow microscopically unstable regions to form; we found that these transitioned to hexagonal polytypes, leading to local trap-assisted performance losses and photoinstabilities. Using surface-bound ethylenediaminetetraacetic acid, we engineered an octahedral tilt into pure α-FAPbI3 thin films without any cation alloying. The templated photoactive FAPbI3 film was extremely stable against thermal, environmental, and light stressors.
|
Dec 2021
|
|
I14-Hard X-ray Nanoprobe
|
Kyle
Frohna
,
Miguel
Anaya
,
Stuart
Macpherson
,
Jooyoung
Sung
,
Tiarnan A. S.
Doherty
,
Yu-Hsien
Chiang
,
Andrew J.
Winchester
,
Kieran W. P.
Orr
,
Julia E.
Parker
,
Paul D.
Quinn
,
Keshav M.
Dani
,
Akshay
Rao
,
Samuel D.
Stranks
Diamond Proposal Number(s):
[19023, 20420]
Abstract: Halide perovskites perform remarkably in optoelectronic devices. However, this exceptional performance is striking given that perovskites exhibit deep charge-carrier traps and spatial compositional and structural heterogeneity, all of which should be detrimental to performance. Here, we resolve this long-standing paradox by providing a global visualization of the nanoscale chemical, structural and optoelectronic landscape in halide perovskite devices, made possible through the development of a new suite of correlative, multimodal microscopy measurements combining quantitative optical spectroscopic techniques and synchrotron nanoprobe measurements. We show that compositional disorder dominates the optoelectronic response over a weaker influence of nanoscale strain variations even of large magnitude. Nanoscale compositional gradients drive carrier funnelling onto local regions associated with low electronic disorder, drawing carrier recombination away from trap clusters associated with electronic disorder and leading to high local photoluminescence quantum efficiency. These measurements reveal a global picture of the competitive nanoscale landscape, which endows enhanced defect tolerance in devices through spatial chemical disorder that outcompetes both electronic and structural disorder.
|
Nov 2021
|
|
I14-Hard X-ray Nanoprobe
|
Sofiia
Kosar
,
Andrew J.
Winchester
,
Tiarnan A. S.
Doherty
,
Stuart
Macpherson
,
Christopher E.
Petoukhoff
,
Kyle
Frohna
,
Miguel
Anaya
,
Nicholas S.
Chan
,
Julien
Madéo
,
Michael K. L.
Man
,
Samuel D.
Stranks
,
Keshav M.
Dani
Diamond Proposal Number(s):
[19023]
Open Access
Abstract: With rapidly growing photoconversion efficiencies, hybrid perovskite solar cells have emerged as promising contenders for next generation, low-cost photovoltaic technologies. Yet, the presence of nanoscale defect clusters, that form during the fabrication process, remains critical to overall device operation, including efficiency and long-term stability. To successfully deploy hybrid perovskites, we must understand the nature of the different types of defects, assess their potentially varied roles in device performance, and understand how they respond to passivation strategies. Here, by correlating photoemission and synchrotron-based scanning probe X-ray microscopies, we unveil three different types of defect clusters in state-of-the-art triple cation mixed halide perovskite thin films. Incorporating ultrafast time-resolution into our photoemission measurements, we show that defect clusters originating at grain boundaries are the most detrimental for photocarrier trapping, while lead iodide defect clusters are relatively benign. Hexagonal polytype defect clusters are only mildly detrimental individually, but can have a significant impact overall if abundant in occurrence. We also show that passivating defects with oxygen in the presence of light, a previously used approach to improve efficiency, has a varied impact on the different types of defects. Even with just mild oxygen treatment, the grain boundary defects are completely healed, while the lead iodide defects begin to show signs of chemical alteration. Our findings highlight the need for multi-pronged strategies tailored to selectively address the detrimental impact of the different defect types in hybrid perovskite solar cells.
|
Sep 2021
|
|
I14-Hard X-ray Nanoprobe
|
Elizabeth M.
Tennyson
,
Kyle
Frohna
,
William K.
Drake
,
Florent
Sahli
,
Terry
Chien-Jen Yang
,
Fan
Fu
,
Jérémie
Werner
,
Cullen
Chosy
,
Alan R.
Bowman
,
Tiarnan A. S.
Doherty
,
Quentin
Jeangros
,
Christophe
Ballif
,
Samuel D.
Stranks
Diamond Proposal Number(s):
[20420]
Open Access
Abstract: Halide perovskite/crystalline silicon (c-Si) tandem solar cells promise power conversion efficiencies beyond the limits of single-junction cells. However, the local light-matter interactions of the perovskite material embedded in this pyramidal multijunction configuration, and the effect on device performance, are not well understood. Here, we characterize the microscale optoelectronic properties of the perovskite semiconductor deposited on different c-Si texturing schemes. We find a strong spatial and spectral dependence of the photoluminescence (PL) on the geometrical surface constructs, which dominates the underlying grain-to-grain PL variation found in halide perovskite films. The PL response is dependent upon the texturing design, with larger pyramids inducing distinct PL spectra for valleys and pyramids, an effect which is mitigated with small pyramids. Further, optimized quasi-Fermi level splittings and PL quantum efficiencies occur when the c-Si large pyramids have had a secondary smoothing etch. Our results suggest that a holistic optimization of the texturing is required to maximize light in- and out-coupling of both absorber layers and there is a fine balance between the optimal geometrical configuration and optoelectronic performance that will guide future device designs.
|
May 2021
|
|
I14-Hard X-ray Nanoprobe
|
Diamond Proposal Number(s):
[20420]
Abstract: Halide perovskites are a versatile class of semiconductors employed for high performance emerging optoelectronic devices, including flexoelectric systems, yet the influence of their ionic nature on their mechanical behavior is still to be understood. Here, a combination of atomic‐force, optical, and compositional X‐ray microscopy techniques is employed to shed light on the mechanical properties of halide perovskite films at the nanoscale. Mechanical domains within and between morphological grains, enclosed by mechanical boundaries of higher Young's Modulus (YM) than the bulk parent material, are revealed. These mechanical boundaries are associated with the presence of bromide‐rich clusters as visualized by nano‐X‐ray fluorescence mapping. Stiffer regions are specifically selectively modified upon light soaking the sample, resulting in an overall homogenization of the mechanical properties toward the bulk YM. This behavior is attributed to light‐induced ion migration processes that homogenize the local chemical distribution, which is accompanied by photobrightening of the photoluminescence within the same region. This work highlights critical links between mechanical, chemical, and optoelectronic characteristics in this family of perovskites, and demonstrates the potential of combinational imaging studies to understand and design halide perovskite films for emerging applications such as photoflexoelectricity.
|
Mar 2021
|
|
I07-Surface & interface diffraction
|
Zahra
Andaji-Garmaroudi
,
Mojtaba
Abdi-Jalebi
,
Dengyang
Guo
,
Stuart
Macpherson
,
Aditya
Sadhanala
,
Elizabeth M.
Tennyson
,
Edoardo
Ruggeri
,
Miguel
Anaya
,
Krzysztof
Galkowski
,
Ravichandran
Shivanna
,
Kilian
Lohmann
,
Kyle
Frohna
,
Sebastian
Mackowski
,
Tom J.
Savenije
,
Richard H.
Friend
,
Samuel D.
Stranks
Diamond Proposal Number(s):
[17223]
Open Access
Abstract: Mixed‐halide lead perovskites have attracted significant attention in the field of photovoltaics and other optoelectronic applications due to their promising bandgap tunability and device performance. Here, the changes in photoluminescence and photoconductance of solution‐processed triple‐cation mixed‐halide (Cs0.06MA0.15FA0.79)Pb(Br0.4I0.6)3 perovskite films (MA: methylammonium, FA: formamidinium) are studied under solar‐equivalent illumination. It is found that the illumination leads to localized surface sites of iodide‐rich perovskite intermixed with passivating PbI2 material. Time‐ and spectrally resolved photoluminescence measurements reveal that photoexcited charges efficiently transfer to the passivated iodide‐rich perovskite surface layer, leading to high local carrier densities on these sites. The carriers on this surface layer therefore recombine with a high radiative efficiency, with the photoluminescence quantum efficiency of the film under solar excitation densities increasing from 3% to over 45%. At higher excitation densities, nonradiative Auger recombination starts to dominate due to the extremely high concentration of charges on the surface layer. This work reveals new insight into phase segregation of mixed‐halide mixed‐cation perovskites, as well as routes to highly luminescent films by controlling charge density and transfer in novel device structures.
|
Sep 2019
|
|
