Open Access

Show Abstract ▼

Abstract: Broadband infrared nanospectroscopy with Synchrotron Radiation, via the atomic force microscope detection of photothermal expansion, was first demonstrated at the MIRIAM beamline of Diamond in 2016. Since then, the system has undergone significant developments and has been available to users in collaboration since January 2018. Continuous nano-FTIR spectra are so-far achieved with useful signal-to-noise in the 4000 – 800 wavenumber region and at around 100 nm spatial resolution (depending on sample geometry and thermal diffusion at the modulation frequency of the IR beam), for soft materials like single biological cells and polymers. Here we briefly describe the nanospectroscopy system and evaluate the performances through comparison of measured data for typical samples with theoretical expectations. Noise levels are shown to be cantilever thermal-noise limited at the first contact resonance currently employed, whilst signal levels are consistent with expectations for the focussed IR power density available from the IR beamline and using sinusoidal modulation of the beam tuned to the contact resonance frequency. Finally, planned enhancements of the performance, including access to higher cantilever contact resonances to reduce noise and increase spatial resolution, are discussed.

Open Access

Show Abstract ▼

Abstract: Photoacoustic spectroscopy (PAS) measures the photon absorption spectrum of a sample through detection of the acoustic wave generated by the photothermal effect as one modulates the intensity of the incident radiation at each wavelength. We have recently demonstrated the implementation of PAS in a microscopy configuration with mid-infrared radiation (microPAS). In the present work, we describe the performance of microPAS using synchrotron radiation (SR) in diffraction-limited spectromicroscopy and imaging experiments. Spectra were obtained for polystyrene beads, polypropylene fibres, and single fibres of human hair. SR produced microPAS spectra of much higher intensity as compared with those obtained using conventional mid- and near-infrared sources. For hair samples, the penetration depth of mid-infrared light, even with bright SR, is significantly shorter than the probed sample thickness at very low modulation frequencies resulting in saturated PAS spectra. In contrast, microPAS spectra of polymer beads were in general of much better quality than those obtained with conventional sources. We also demonstrated the capability to collect line profiles and line spectra at diffraction limited spatial resolution. The microPAS spectra of beads appear free from appreciable bandshape distortions arising from the real part of the refractive index of the sample. This observation confirms microPAS as an absorption-only technique and establishes it as a valuable new tool in the microspectroscopic analysis of particulates and of samples with a complex topography.

Show Abstract ▼

Abstract: Research on the broadband dielectric response of metal-organic frameworks (MOFs) is an emergent field that could yield exciting device applications, such as smart optoelectronics, terahertz sensors, high-speed telecommunications and microelectronics. Hitherto, a detailed understanding of the physical mechanisms controlling the frequency-dependent dielectric and optical behavior of MOFs is lacking because a large number of studies have focused only on static dielectric constants. Herein we employed high-resolution spectroscopic techniques in combination with periodic ab initio density functional theory (DFT) calculations to establish the different polarization processes for a porous copper-based MOF, termed HKUST-1. We used alternating current measurements to determine its dielectric response between 4 Hz and 1.5 MHz where orientational polarization is predominant, while synchrotron infrared (IR) reflectance was used to probe the far-IR, mid-IR, and near-IR dielectric response across the 1.2 THz to 150 THz range (ca. 40 – 5000 cm-1) where vibrational and optical polarizations are principal contributors to its dielectric permittivity. We demonstrate the role of pressure on the evolution of broadband dielectric response, where THz vibrations reveal distinct blue and red shifts of phonon modes from structural deformation of the copper paddle-wheel and the organic linker, respectively. We also investigated the effect of temperature on dielectric constants in the MHz region pertinent to microelectronics, to study temperature-dependent dielectric losses via dissipation in an alternating electric field. The DFT calculations offer insights into the physical mechanisms responsible for dielectric transitions observed in the experiments and enable us to explain the frequency shifts phenomenon detected under pressure. Together, the experiments and theory have enabled us to glimpse into the complex dielectric response and mechanisms underpinning a prototypical MOF subject to pressure, temperature, and vast frequencies.

Show Abstract ▼

Abstract: Emissions of SO2 from flue gas and marine transport have detrimental impacts on the environment and human health, but SO2 is also an important industrial feedstock if it can be recovered, stored and transported efficiently. Here we report the exceptional adsorption and separation of SO2 in a porous material, [Cu2(L)] (H4L = 4′,4‴-(pyridine-3,5-diyl)bis([1,1′-biphenyl]-3,5-dicarboxylic acid)), MFM-170. MFM-170 exhibits fully reversible SO2 uptake of 17.5 mmol g−1 at 298 K and 1.0 bar, and the SO2 binding domains for trapped molecules within MFM-170 have been determined. We report the reversible coordination of SO2 to open Cu(ii) sites, which contributes to excellent adsorption thermodynamics and selectivities for SO2 binding and facile regeneration of MFM-170 after desorption. MFM-170 is stable to water, acid and base and shows great promise for the dynamic separation of SO2 from simulated flue gas mixtures, as confirmed by breakthrough experiments.

Open Access

Show Abstract ▼

Abstract: Fourier-transform infrared (FTIR) spectroscopy is a widespread and highly sensitive analytical method for the identification and characterization of a wide range of materials via their infrared (IR) absorption bands. Until now, the potential of IR microspectroscopy and imaging for the characterization of works of art or other objects of cultural heritage significance has been only partially exploited; in particular the use of the synchrotron radiation (SR) IR microprobe to study, at the micron scale, materials of interest for archaeological and cultural heritage studies has become popular only in the past decade. One of the main requirements imposed on the studies of ancient and/or valuable materials is that the techniques applied must be non-destructive. In this scenario, SRbased FTIR methods are perfectly suitable. Moreover, IR spectroscopy and imaging are emerging techniques that combine the assets of IR in terms of molecular specificity with the unique properties of synchrotron light. SR-FTIR micro-spectroscopy offers great advantages over conventional methods because it provides a broader spectrum (down to THz) and higher spectral quality (signal/noise ratio) at the highest spatial resolution (diffraction limited). This is due to the high brilliance and collimation of SR-IR, while still being non-damaging to the investigated system. The unique SR-IR parameters are essential for the compositional analysis of the tiny, sub-millimetric samples characteristic of ancient materials, which are heterogeneous by nature, and with complex molecular distributions at extremely variable concentrations. SR-FTIR spectroscopy and imaging can be applied successfully to the characterization of organic and inorganic materials via so-called IR fingerprinting, as well as for their compositional quantification. The range of materials investigated is very broad and encompasses painting materials, stones, glasses, ceramics, coatings on metals, paper and wooden materials, canvas or other textiles, organic colourants, resins, varnishes, cosmetics, and binding media such as glues, waxes, oils, etc. SR-IR-based methods can also be used to understand the historical technologies and to identify the raw materials used to produce archaeological artefacts and art objects, and to improve stabilization, conservation and restoration practices. Selected applications of SR-FTIR methods are discussed with a special emphasis on the chemical and mineralogical characterization of ancient paintings, on the study of alteration and corrosion layers, and the separation and identification of pigments. New perspectives offered by existing facilities and new developments in IR imaging and advanced vibrational spectroscopy that may broaden the variety of archaeological and historical materials that may be studied are outlined.