Open Access

Show Abstract ▼

Abstract: Photoelectron spectroscopy is a powerful characterisation tool for semiconductor surfaces and interfaces, providing in principle a correlation between the electronic band structure and surface chemistry along with quantitative parameters such as the electron affinity, interface potential, band bending and band offsets. However, measurements are often limited to ultrahigh vacuum and only the top few atomic layers are probed. The technique is seldom applied as an in situ probe of surface processing; information is usually provided before and after processing in a separate environment, leading to a reduction in reproducibility. Advances in instrumentation, in particular electron detection has enabled these limitations to be addressed, for example allowing measurement at near-ambient pressures and the in situ, real-time monitoring of surface processing and interface formation. A further limitation is the influence of the measurement method through irreversible chemical effects such as radiation damage during X-ray exposure and reversible physical effects such as the charging of low conductivity materials. For wide-gap semiconductors such as oxides and carbon-based materials, these effects can be compounded and severe. Here we show how real-time and near-ambient pressure photoelectron spectroscopy can be applied to identify and quantify these effects, using a gold alloy, gallium oxide and semiconducting diamond as examples. A small binding energy change due to thermal expansion is followed in real-time for the alloy while the two semiconductors show larger temperature-induced changes in binding energy that, although superficially similar, are identified as having different and multiple origins, related to surface oxygen bonding, surface band-bending and a room-temperature surface photovoltage. The latter affects the p-type diamond at temperatures up to 400 °C when exposed to X-ray, UV and synchrotron radiation and under UHV and 1 mbar of O2. Real-time monitoring and near-ambient pressure measurement with different excitation sources has been used to identify the mechanisms behind the observed changes in spectral parameters that are different for each of the three materials. Corrected binding energy values aid the completion of the energy band diagrams for these wide-gap semiconductors and provide protocols for surface processing to engineer key surface and interface parameters.

Show Abstract ▼

Abstract: In situ photoemission and near-edge X-ray absorption fine structure (NEXAFS) techniques have been used to study the interaction of CO2 with an ionic liquid thin film. A thin film of the superbasic ionic liquid (SBIL) trihexyltetradecylphosphonium benzimidazolide ([P66614][benzim]) was prepared on a rutile TiO2 (110) surface and exposed to CO2 at near-ambient pressures. NEXAFS measurements combined with density functional theory calculations indicate a realignment of [benzim]− anions from 27° from the surface normal to 54° upon exposure to CO2. Angle-resolved X-ray photoelectron spectroscopy (AR-XPS) shows evidence of irreversible CO2 absorption in thin films of [P66614][benzim] and a greater concentration of CO2-reacted anions in the deeper layers. These results give a new perspective on CO2 uptake in ionic liquids and fundamental interactions at the liquid–gas interface. Understanding this interfacial behavior is important for developing ILs for gas capture applications and may influence the performance of other IL-based technologies.

Show Abstract ▼

Abstract: The commercial catalysts currently used to remove polluting gases from vehicle exhausts rely on expensive precious metals, with demand continually growing. Preparing these catalysts often requires solvents, waste treatment and elevated temperatures, all with an environmental cost. One solution is to investigate the use of an alternative, more abundant material. LaMnO has shown promising catalytic behaviour and is made by physically mixing two solid reactants. The catalytic activity of materials is highly dependent on how they are produced. In this work, researchers synthesised LaMnO3 by a novel method, ball milling, to improve its catalytic properties. To replicate or optimise the final material structure, it is vital to investigate the chemical steps occurring within the ball mill. However, the ball mill setup makes it difficult to perform real-time analysis. Therefore, the research team replicated the conditions experienced within the ball mill by applying extreme pressures to the starting materials. Using Diamond Light Source’s Energy Dispersive EXAFS beamline (I20-EDE) meant they could monitor how the structure changes with increasing pressure, using X-ray Absorption Fine Structure (XAFS) measurements in real-time. This beamline setup also allowed them to use a specialised high-pressure cell. They used complementary measurements on Diamond’s Versatile Soft X-ray (VerSoX) beamline (B07) to study the surface properties of the materials during catalysis. Beamline I20-Scanning was used to look at electronic structure. For industrial companies researching ball milling as an alternative production route, i.e. for autocatalysis or battery materials, this research highlights that though the preparation route produces beneficial properties at a lower environmental cost, understanding its underlying chemistry is hugely challenging.

Open Access

Show Abstract ▼

Abstract: Near ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) was used to study the chemical states of a range of alumina-supported monometallic Pd and bimetallic Pd-Pt nanocatalysts, under methane oxidation conditions. It has been suggested before that for optimal complete methane oxidation, palladium needs to be in an oxidised state. These experiments, combining NAP-XPS with a broad range of characterisation techniques, demonstrate a clear link between Pt presence, Pd oxidation, and catalyst activity under stoichiometric reaction conditions. Under oxygen-rich conditions this behaviour is less clear, as all of the palladium tends to be oxidised, but there are still benefits to the addition of Pt in place of Pd for complete oxidation of methane.

Show Abstract ▼

Abstract: The reaction of ammonia oxidation over PtRh binary alloy has been studied with a surface science approach by operando techniques such as Near Ambient Pressure X-Ray Photoemission Spectroscopy (NAP-XPS) and Surface X-Ray Diffraction (SXRD) combined with mass spectrometry. The article will explore the surface evolution across five different oxygen to ammonia ratios in the millibar regime for two different temperatures. The presented data-set allows to link variations in the atomic structures measured by diffraction methods and surface species information from NAP-XPS to reaction products in the gas phase. We will show that NO production coincides with significant changes of the surface structure and the formation of a RhO2 surface oxide. It was also observed that the RhO2 surface oxide only fully forms when the nitrogen signal in the N1s has disappeared.